MIL-T-62110 Trucks, Maintenance: With Rotating Hydraulic Derrick, 32,000 To 44,500 Gvw, 4X2, 4X4, 6X4, And 6X6, CommercialThis specification covers maintenance trucks with a rotating and telescoping hydraulic derrick. Vehicles procured under this specification are commercial items which are warranted by the manufacturer as specified in acquisition documents.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58

MIL-T-6211OG

leaving the cab. When the front tires extend beyond the cab fenders, rubber fender extensions extending at least to the outside of the tire tread shall be furnished. When tilt type cabs are furnished, provisions to facilitate cleaning the windshield shall be provided by means of a bumper step or bumper step cutouts and a grab handle located under the windshield. When step height exceeds 24 inches, a secondary step shall be provided.

3.4.12.1 Cab interior. Unless otherwise specified, the cab shall have an upholstered, full width, adjustable seat and back or individual, adjustable, driver's seat and individual passenger seat. When specified (see 6.2), an individual, adjustable, driver's seat and an individual passenger seat shall be provided. When specified (see 6.2), the driver's seat shall be the manufacturer's standard air ride suspension type. The color of the upholstery and the interior finish shall be compatible with the exterior color (see 3.1.1.1). White upholstery shall not be furnished. Interior lighting shall be provided. Two pairs of seat belts shall be installed.

* 3.4.12.2 Crew cab. When specified (see 6.2), a four-door, full width crew cab shall be furnished in lieu of the standard full width cab. The cab shall be equipped with two upholstered, full width seats and backs. The front seat shall be adjustable. Three pairs of seat belts shall be installed for both the front and rear seats. Cab doors shall be equipped with locks operable from inside the cab through mechanical linkage, with both front doors equipped with an external key operated lock. Cab doors shall have windows with crank operated window regulators. A rear window shall be provided. Interior lighting shall be provided. Safety grips or grab handles shall be provided at each door of the cab to assist personnel climbing into the cab. The cab roof shall be of one-piece construction; or, if welded, the roof shall give the appearance of one piece, with weld seams being continuous, waterproof , and free of visible seams, bumps or protrusions. Full length drip moldings shall be mounted above the doors. When a crew cab is furnished, the

cab-to-axle dimension shall be measured from the back face of the crew cab.

3.4.12.3 Crew cab seat spacing. With the front seat adjusted to the extreme forward position there shall be not less than 3O inches, measured in a horizontal plane, between the front of the rear seat-back and the rear of the front seat-back. A kick-space height of not less than

2.75 inches shall be maintained between the floor and the rear of the front seat in all positions of adjustment. Leg room and space forward of the front seat shall be equivalent to that provided ahead of the seat in a two-door standard cab.

3.4.13 Steering. Power steering shall be furnished.

3.4.14 Windshield wipers and washers. The vehicle shall be equipped with dual windshield wipers and windshield washers. The windshield wipers shall be multispeed type operated by either air or electric motor(s).