MIL-T-62032 Trucks, Tank: Fuel Servicing And Aircraft Fuel Servicing, 1,000 To 4,000 Gallon, Diesel And Gasoline Engine Driven, 16,000 To 50,000 Pounds Gvw, 4X2, 4X4, 6X4, And 6X6, Modified CommercialThis specification covers diesel and gasoline engine driven, four-wheel, two- or four-wheel drive, and six-wheel, four- or six-wheel drive, single or dual delivery fuel servicing and aircraft fuel servicing tank trucks, with product capacities from 1,000 to 4,000 gallons, having minimum gross vehicle weights GVW of 16,000 to 50,000 pounds for normal operating conditions. Vehicles procured under this specification are commercial items which are warranted by the manufacturer as specified in acquisition documents.

Pages 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8 - 9 - 10 - 11 - 12 - 13 - 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 25 - 26 - 27 - 28 - 29 - 30 - 31 - 32 - 33 - 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41 - 42 - 43 - 44 - 45 - 46 - 47 - 48 - 49 - 50 - 51 - 52 - 53 - 54 - 55 - 56 - 57 - 58 - 59 - 60 - 61 - 62

MIL-T-62032H

passenger seat shall be provided. The color of the upholstery and the interior finish shall be compatible with the exterior color (see 3.1.1.1). White upholstery shall not be furnished. Interior lighting shall be provided. Seat belts shall be installed.

3.4.13 Steering. Power steering shall be furnished.

3.4.14 Windshield wipers and washers. The vehicle shall be equipped with dual windshield wipers and windshield washers. The windshield wipers shall be of the multispeed type and operated by either air or electric motor(s).

3.4.15 Front bumper. Unless the front bumper is an integral part of the vehicle cab, a channel type front bumper shall be provided.

3.4.16 Rear bumper. A rear bumper shall be provided and shall conform to Federal

Motor Carrier Safety Regulation 393.86 and 49 CFR, section 178.340, specification MC-306.

3.4.17 Tool stowage. Stowage space of sufficient size to accommodate a vehicle jack, hand tools, antiskid chains and emergency reflective triangles shall be furnished for retaining equipment during vehicle operation. Stowage space for these tools may be furnished in the cab. When stowage space is located outside the cab, it shall be weatherproof and shall provide for locking with a padlock.

3.4.17.1 Tools. When specified (see 6.2), the vehicle shall be furnished with tools required for exchanging a mounted tire assembly with the spare assembly, and shall include at least a hydraulic jack, jack handle and wheelnut wrench. The jack shall be of such closed height as to permit its location under an axle, or other satisfactory lift point, at any wheel with the tire flat. The jack, without blocking, shall be capable of raising any wheel of the loaded vehicle to a height adequate to permit removal and replacement of the wheel and tire assembly.

3.4.18 Heater and defroster. A hot water heater shall be provided. The heater shall have fresh air intakes. Discharge outlets shall be provided to direct heated air to the floor and to the defroster louvers. The heater shall be complete with a blower and mounted controls convenient to the driver.

3.4.19 Controls and operating mechanisms. All controls and operating mechanisms shall be located for left hand drive. Controls shall be complete and conveniently operable by the driver. Lever controls shall be designed and located to permit easy entrance and exit of the operator to and from the driver's compartment. Instruments and controls shall be identified as to their function and installed in a manner to facilitate removal and servicing. Instruments shall be visible to the driver when seated in driving position.